Why Learning Plumbing Basics is Essential for Installing a Bathtub
Why Learning Plumbing Basics is Essential for Installing a Bathtub
Blog Article
How do you really feel in relation to A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't specifically brain surgery, however it does call for strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably challenging job. If the old tub is conveniently available, the job can relocate rapidly; if you have to open a wall surface to remove the old tub and also position the new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will require an assistant to leave the old bathtub as well as set in the new one. See to it you have actually certified on your own for the work and fit trying it. As opposed to working with a professional to take over a halfway-completed job, it is far better to take into consideration using one prior to you start. Chances are you may require an expert plumber to make tube connections.
This post will aid you install a brand-new bath tub in your washroom if you have actually currently bought a new tub and do not need to alter the setup of your previous water pipes.
Your devices and also material checklist must comprise the following:
Getting ready for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic because of the restricted accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old sealing substance.
Before going on to fit the new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Utilizing both wood boards under its feet, put the bath tub in the needed placement. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bath tub till the spirit level checks out level.
To set up faucets, fit the bottom of the outermost flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the water system and also inspect all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as likewise check the overflow electrical outlet and also the normal outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait till the bathtub has actually been made use of at the very least once as this will resolve it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin making sure that the washing machines are in area between the faucet and the sink. Protect the faucet in place with the producer given backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type must be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, causing the water to pass through the wall surface between the bathroom and the tiling, causing complications with wetness and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water before securing, to allow for the motion experienced when the tub is in usage. The sealer can break fairly very early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily offered on the marketplace. It is recommended to fit the floor tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about Installing A Bathtub? Give feedback down below. We would be glad to know your reactions about this piece. We hope that you visit us again soon. For those who enjoyed our blog post plz do not forget to pass it around. Thanks a lot for your time spent reading it.
Request plumbing analysis. Report this page